Readers ask: How To Read Gas Meter Ireland?

0 Comments

How do you read a gas meter in Ireland?

Reading your Gas Meter The four small dials at the bottom should be read from left to right. The position of the pointer on the dial indicates what the reading should be. If the pointer is between two figures, use the lower figure, e.g. if it is between 7 and 8, use 7. However, if the pointer is between 9 and 0, use 9.

How do I read gas meter?

To read correctly:

  1. Read the dials from left to right.
  2. If the pointer is between two numbers, always take the lower number.
  3. If the pointer falls between 9 and 0, write down 9.
  4. Ignore red dials, ones marked ‘100 per rev’ and the largest dial.

How do I read my gas meter A and B buttons?

If your meter has a green A and a white B button:

  1. Press and hold the green A button for at least 2 seconds.
  2. Press A again and again to cycle through the displays.
  3. The first row of numbers you’ll see is your meter reading.
You might be interested:  Question: What Is A Civil Case In Ireland?

Where is my gas meter Ireland?

When new meters are installed, they are located in external meter boxes. For older homes, the meter may be inside the home.

Where would my gas meter be located?

Gas meters are generally contained in a meter box or meter cabinet located outside the premises at the front or front side of the building. If you can’t locate the meter, please contact your letting agent or landlord.

What does M3 mean on gas meter?

Digital metric meter Digital metric gas meters measure gas usage in cubic meters ( m3 ) and usually show ‘M’ or ‘ M3 ‘.

What is a low gas meter reading?

Two rate meters It records two readings, one for your day usage and one for night usage. Day usage is called ‘normal’ and night usage is called ‘ low ‘. For instance the electricity meter above would be recorded as: Low (night): 80506. Normal (day): 97192.

What button do I press to get a meter reading?

Meters with a Keypad All you need to do is press ‘9’ on the keypad. The word VOLUME will appear on the screen then you will see a row of digits folowed by M3. Note down the numbers before the decimal point, ignoring any zeroes at the start. This meter reading is 45.

What is the B button for on my gas meter?

This is your electricity reading. If your meter has an ‘A’ and ‘ B ‘ button, press ‘A’ until you get to TOTAL ACT IMPORT. The number below this is your electricity reading.

You might be interested:  Readers ask: How Much Does A Tesla Cost In Ireland?

How do I get a gas meter reading from a smart meter?

If you have a keypad To get a reading from these smart meters: Press 9 on the keypad until you se ‘VOLUME’ on the display. Then you’ll see a row of digits (e.g. 00063.5) followed by M3 at the bottom right of the screen. This is your reading.

What does a SMETS2 meter look like?

If the serial number starts with 19P, this indicates it’s a SMETS1 meter. If it starts with 19M, then this means it’s SMETS2. Another way to tell is to look for a Telefonica/Arqiva/WNC/Toshiba device with two to five LED lights on top of your electricity meter. If you can see one, then you have a SMETS2 meter!

Who is responsible for gas meter box?

Gas meter boxes can be installed by the homeowner before the supplier installs the supply, or the gas supplier might install the meter box through some agreement with the consumer. However, once the meter box is installed it appears that the consumer (usually the property owner) is responsible for its maintenance.

Who is responsible for installing a gas meter?

The supplier will install a meter on your property, so you should choose them in good time before you want the connection to take place, in order to avoid delays. You might have to pay for this installation – it depends on the supplier.

What does B3 mean on gas meter Ireland?

If you get a ‘ B3 ‘ error message on your gas meter, it means the battery is low and the meter needs to be replaced.

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Post